- Does drip edge go over fascia?
- How much should shingles overhang drip edge?
- Does roof flashing go under shingles?
- What color drip edge should I use?
- How much does drip edge cost?
- What is the difference between drip edge and rake edge?
- Do you need drip edge on gable ends?
- How far should Roof sheathing overhang fascia?
- Do you caulk drip edge?
- Can drip edge be painted?
- What size drip edge should I use?
- Can you install drip edge after shingles?
- Does drip edge go over felt paper?
- Should roof sheathing be flushed with fascia?
- Should shingles extend past drip edge?
- How do I extend the drip edge on my gutters?
- Should drip edge be tight against fascia?
- Should you use drip edge touch fascia?
- Should gutters be installed under drip edge?
Does drip edge go over fascia?
Drip edge flashing directs roof runoff away from the roof fascia and edge and into gutters or at least not down the fascia board (if no gutters are installed) and it is recommended by roofing standards, manufacturers, and experts..
How much should shingles overhang drip edge?
Asphalt shingles should overhang the exterior edge of the drip edge by ¼ to ¾-inch. Check local building code for drip edge requirements prior to the start of your roofing project.
Does roof flashing go under shingles?
Flashing should overlap the roof-covering material, but on asphalt shingle roofs, for aesthetic reasons, the part of the headwall flashing that extends down over asphalt shingles is often covered with a course of shingle tabs. … Wind-driven rain can enter at these gaps, causing roof leaks.
What color drip edge should I use?
If your home’s trim and fascia are white, it is recommended you select a white drip edge for seamless blending of elements throughout. If your home has more pops of brown, similar to the home displayed in the photo to the right, you may want to choose a brown drip edge.
How much does drip edge cost?
Drip Edges: $1-$2 per linear foot installed. Inspect and replace drip edges as necessary. Drip edges are added to the roof to direct water into the gutters. Other Damage – Have a professional inspect your eaves for damage before repairing fascia and soffits.
What is the difference between drip edge and rake edge?
Drip edge and rake edge are the first parts of the roof system to be installed. … They form a long, narrow piece of metal, which is installed along the perimeter your Roof Deck. Drip edge goes along your eaves trough areas and rake edge goes along your gable ends.
Do you need drip edge on gable ends?
Drip edges also help prevent shingles at the end of a roof from cracking, sagging, and becoming limp. Drip edges can also be installed on the gable ends of a roof. They add a clean, trimmed look to a roof while preventing water from entering into undesirable areas.
How far should Roof sheathing overhang fascia?
Too much overhang and the shingles could blow off in high winds; too little can allow water to seep into rake or fascia boards. 10. Incorrect shingle exposure. For standard three-tab shingles, an exposure of five inches is suggested.
Do you caulk drip edge?
No, dont caulk under it. Its not supposed to be caulked. Its designed to drain, if you caulk it & water gets under your roof system somehow the caulking would create a dam causing ice or water to back up & cause a leak elsewhere.
Can drip edge be painted?
Yes you can paint the aluminum drip edge and it hold up very well. Just be sure it is clean and paint it with a good exterior acrylic primer and finish with a exterior acrylic semi-gloss house paint.
What size drip edge should I use?
I usually select drip edges with at least a 4-inch roof leg along the eaves edge and a 2-inch leg along rakes. The code calls for the fascia/rake leg to extend 1/4 inch below the roof sheathing and the Fortified Home guides call for 1/2 inch. But I like to use drip edge with at least a 1-inch fascia/rake leg.
Can you install drip edge after shingles?
The drip edge is often replaced when new shingles are installed, but it can be replaced at any time. Asphalt roof shingles can become brittle in cold weather, so wait until a warm (but not hot) day to remove and replace eave stripping.
Does drip edge go over felt paper?
Installing roof drip edge flashing properly The best way is to install the roof drip edge only along the eaves first, then place ice-and-water barrier (in the snowbelt) or felt paper (underlayment) over the drip edge. This lets any water that gets on the roof run down the underlayment and over the drip edge.
Should roof sheathing be flushed with fascia?
To my way of thinking, the sheathing should overlap the rafters by the thickness of, and possibly even rest on top of, the fascia board. As you can see in the photo, it is flush with the rafter ends and little support is provided for the drip edge.
Should shingles extend past drip edge?
Shingles should not extend more than 3/4” (19 mm) past the drip edge. If shingles overhang the edge of the roof by more than 3/4” (19 mm), then they are not supported and may crack and break off.
How do I extend the drip edge on my gutters?
If the gutter is mounted too far below the drip-edge, or if the kickout doesn’t extend far enough over the gutter, a retrofit solution would be to slip a strip of metal or rigid plastic flashing under the vertical fascia leg of the drip-edge and let the bottom edge of the strip overlap the back edge of the gutter.
Should drip edge be tight against fascia?
The drip edge should be installed over a piece of 1×2 furring strip so that it stands off from the fascia or rafter tails. If the drip edge is laid right up against the fascia or rafters, then because of surface tension, the water runs right up against the fascia and underneath the soffit.
Should you use drip edge touch fascia?
If the home has no gutter, the drip edge will prevent the water from running down the fascia and onto or into the soffit cavity. However, without the drip edge, the water sticks to shingles, potentially working its way under the shingles to cause a leak.
Should gutters be installed under drip edge?
Your gutter needs to be a few inches under the edge of your roof. … Drip edge gets installed under the first course of shingles and promotes water to run freely from roof edge down into gutter. Without it, water may run down behind your gutter, down fascia board and siding, leading to potential damage.